How deep is a deep well socket?

A deep socket will generally be around one inch long. This will allow you to use a socket wrench in inaccessible places, especially if you have an extension on the driver.

Deep sockets are useful for turning nuts onto bolts when the bolt extends upwards into the socket (as in the case of many bolted joints), a very typical example being exhaust clamp bolts on a car.

Subsequently, question is, what does drive size mean for sockets? Drive Hole indicates the size of the drive hole (also referred to as the “driver hole” or “square hole”), which determines the torque size of the driver tool you’ll need. For example, you’d use a ½-inch drive socket with a ½-inch drive ratchet. L indicates the overall socket length.

Also, what is the most common socket drive size?

10mm sockets and 36mm sockets are typically the most commonly used sizes.

How much torque can a 3/8 ratchet handle?

depending on the size, 130 foot-pounds of torque is within the capability of 3/8, at least at 3/4″ / 19mm.

Are 6 point or 12 point sockets better?

Answer: It’s true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners. Here’s why: (1) Six-point sockets have thicker walls, so they’re less likely to flew.

Are impact sockets different than regular sockets?

Impact sockets look black because the surface is carbonized (aka drop-forged) in order to harden the surface. The surface-hardening enables impact sockets to absorb sudden torque changes (aka “impact”) better. With high enough impact, a regular socket may warp out of shape because the steel used there is softer.

Should I get shallow or deep impact sockets?

Shallow are good for smaller bolts and where you need clearance, but deep sockets are saviors for those hard-to-reach bolts and will let you get a better grip on nuts threaded far down a blind bolt/stud.

Do I need a deep socket for lug nuts?

You will need to use a shallow to be able to start the nut on the lug. I usually put the nut in the socket on a short extension and finger start the nut. So to answer the question, 21 mm short socket if your putting a kit together to carry around in the car. generally deep wells are the way to go.

Can I use impact sockets for everything?

If it’s there then you can use impact sockets for everything. Without enough room they become useless. Impact sockets do wear out faster because they are softer, but that probably doesn’t matter.

Can you use impact sockets with a breaker bar?

The short answer is yes, with some minor caveats. Depending on what you’re wrenching on, an impact socket can be used in place of a normal socket when using a normal (non-impact) ratchet. Similarly, it is safe to use an impact socket on a hand ratchet (although not vice versa).

What is the best socket set?

The Best Socket Set Stanley STMT71648 Socket Set. Dewalt DWMT73804 Drive Socket Set. Craftsman 50230 Mechanics Tool Set. Niko 10074A Hex Bit Socket Set. Stanley 92-824 Black Chrome and Laser Etched Socket Set. Tekton ¾-inch Drive Socket Set. Great Neck Saw PSO40 Drive Socket Set. Astro 7412 ¼-Inch Drive Flex Socket Set.

How long are deep well sockets?

You’ll find that the sockets, both deep and standard, have either 6 points or 12 points, although you can also buy 8 point sockets which work well with square bolts. A deep socket will generally be around 1 inch long.

How much torque can a 1/4 drive take?

1/4 drive, rated for up to 90 ft/lbs of torque.

Can you use a deep socket for spark plugs?

Re: Deep sockets for spark plugs I use regular deep well sockets for spark plugs unless clearance is an issue, which is rare.

How do I know what size socket I have?

How to Determine the Right Size Socket for a Nut Turn on the digital caliper and set it to read in inches, not millimeters. Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides. Check the caliper display. Turn on the digital caliper and set it to read in millimeters, not inches.

How do I know what size socket I need?

Place the end of a measuring tape on one of the flat sides of the nut’s outer perimeter. Stretch the tape measure across the nut’s diameter to the flat-side directly across from the one your pulling from. If the nut is metric, count the number of lines on the tape measure to find the measurement.

How many socket sizes are there?

Therefore, it’s important to choose the precise socket size that fits the particular fastener. There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters).

How do you tell what size a ratchet is?

Drive sizes 1/4 inch – Used for smaller sockets and precision work. 3/8 inch – The middle sized, and in my opinion, most useful size for general use on a car. 1/2 inch – 1/2″ sockets are generally used for nuts and bolts from around 10mm and up.